*AKRAPOVIC exhausts are designed for racing. *There may be changes in product specifications due to the manufacturer's reasons.
* The image is only for reference. The image shown may differ from the actual product.
Based on the volume of a standard vehicle, this model complies with the European noise regulation "Euro 1".Silent type exhaust with baffle on the silencer end.
A line that is similar in concept to the bolt on line, but with the inclusion of a replacement link pipe to bring it closer to the race like feel.The changes in appearance are significant, and some vehicles are equipped with titanium link pipes.Together with bolt on line, the line allows you to experience the high performance of Akrapovic at a low cost. The Akrapovic exhaust system is used by many of the top teams in the world's most famous races such as MOTO GP, WSB, and AMA.This is a superb product that combines advanced technology and craftsmanship at a high level. The performance, quality, and sound of this product will ensure maximum satisfaction and results for the rider and team who receive it.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
With Baffle state, NORMAL and the same etc. The volume of. However, the bass was emphasized, the power increased. Sound changes from around 4000 rpm, it makes Race ish feeling. It improves rushing well and I want to pull it with a low GEAR. Just a little slow Torque is descending or it was necessary to raise the revolution speed slightly at the start. Installation accuracy is no problem, Carbon stay is also Exactly, fine adjustment which is likely to be in other company products is not necessary. However, Bolt of 15 mm? For installation of Center / Be careful as Nut is used. (I installed with Inch size Socket and Pliers) In the case of Z 800, there is a heat shield plate in the Exhaust pipe part if it is NORMAL, but this seems to have been more effective than expected, and if you do not have a heat shield plate Right When you put on your feet hot air I began to feel. I think that this is the same for any outside Exhaust System, so those who are worried may be ants rolling heat-resistant Vantage.View Detail
Design, texture and construction are all good! The weight is light and the product precision is perfect. If you remove the Baffle, the sound is very powerful. Good sound, not annoying in my opinion. Full Exhaust System is also available by adding Header.View Detail
This time I installed an e26 (Slow Veneer with Akrapovic) approved Silencer. The order was placed via PLOT, but the translation (there is no InstallationGuide to enter here, but it was basically a light maintenance Level that anyone could work with while looking at the pictures.
In Stock condition, it is quieter than OEM thanks to the Inner baffle. SilencerBody is stamped with Race Use. The volume becomes small, but the quality of the sound is thick and humid, and it became a crisp sound.
The following is a story from my dream. As for the Inner baffle, it is fastened from the inside with a Bolt and has welding points. (Bolt is stuck from the inside of the exhaust port to the outside) It has a 4mmHex head on the inside of the Bolt, if you know what I'm talking about. I thought there was a nut in the carbon silencer end that was receiving the Bolt, but the tap was cut on the silencer body side and it seemed to stop at 1 pc of Bolt. There are various specs on this point, and I've done a lot of research myself, so I hope this information is useful to someone. The volume in its original form sounds bad at the closing Level. I'm in a dream.
The overall work is relatively light maintenance Level, but there are two points. The diameter of the main pipe is quite tight, so I had to push it a little harder to make the connection. Also, it may not seem necessary to relocate the Center Stand Receiver Rubber, but you should do it properly. The Rubber relocation may be the hardest part of this installation.
Oh, you'll need Torque's T45 for installation. Please prepare in advance.View Detail
I have a BMW R1150R 2001. This AXIS Lab Bitch Slip-on Silencer Titanium is for the R1150GS but is completely compatible with the R1150R. It was installed without any problems. I have replaced the Catalyzer with a REMUS YPIPE and of course the installation is fine. By removing the Catalyzer and replacing the Exhaust System, the weight was reduced by 9.1kg. And the exhaust sound is now nice and dry. If you would like to replace the AXIS Lab Bitch Exhaust System on your R1150R, please contact us. G S isView Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!