Material: made of aluminum 80mm long Recommended rear shock length: 285mm Recommended wheel size: 2.50-8"- 3.00-10" (*12" is not available.)
*Drive chain needs to be replaced.40mm long is 100 links, 80mm long is 110 links, and 160mm long is 120 links. *Stock drum brake, rear disc brake kit can be installed. *Always perform quick chain adjustment with the axle shaft fully loosened and jacked up.
Here is the instruction manual. Other types here [Repair parts] Common repair parts for swing arm Brake Rod (for 40mm long) (38029) Brake Rod (for 80mm long) (27506) Brake rod (for 160mm long) (27505) Pivot gauge (31463) Stepped flat washers (45669) Needle bearing (32002) Rear shock mounting bolt (32068) Axle shaft (69266) Rear Shock Step Nut M10 & Offset Spacer (69267) Repair parts for aluminum swing arm Chain slider (27885) Drum panel bolt (31987) Chain adjuster (47601) Chain adjusting bolt set (47602)
The main pipe is made of extruded aluminum with a different shaped hexagonal cross section (20mm x 30mm) to reduce unsprung weight and to ensure sufficient suspension rigidity. Needle bearings are used in the pivot section for smooth operation even under hard driving conditions. Quick chain adjuster mechanism for quick and easy axle shaft adjustment. Compatible with 8" and 10" wheels (not wide). Chain slider included.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I use it with MONKEY in combination with Rear shock made by 280 mm SHIFT UP. Pivot part (Swingarm body mounting part) For the adjustment of Clearance it is kind that the Washer is attached with Stages. Actually, since there was some play in assembling, it was possible to adjust with Washer included. I do not want it. (It's true) However, is it myself that only one of the Stickers can be included? Below is a supplement to the photo for your reference.
(photo1) ☆ Length 8mm long modestly. By the way, when empty, the above combination will increase the car height by 30 mm. I think that it will be helpful for everyone since such concrete example numbers have not been disclosed to Manufacturer. One more thing, Sprocket F 16 / In R 31 Chain was 90 LINK. (SwingarmChain adjustment center value) (Photo 2) ☆ OEM or OEM look Long Swing Arm feel uncompromising rigidity. (Photo 3) ☆ Needle bearing for Smooth movement! ☆ Chain slider is a little unreliable, but there are no traces like it was scraped even after traveling 300 kilometers. (Photo 4) ☆ Compared to other companies Swingarm the surface is dull and there is no shine, so Buffing was applied. Also, since the ChainAdjust part at the rearmost end is the casting itself, Grinderetc. Also use gradually raise the count gradually and go buffing. Well, I like this kind of fun, is not it? Rear tire When assembling, it is considerably hub tight against the inside width of Swingarm in Free state As the size diminishes Small, add Washer to make Swingarm impossible without impossibility did. (Photo 5) ☆ ChainAdjust is somewhat difficult to use. Of course you can adjust. Although not shown in this picture, there was not interference between Swingarm and Rear brake switch.
Although as [ 8 inches ] was decided on, when I may have wished to use 10 inches in the future, the tire was 80 mm with which it can equip no less than 10 inches again so that a swing arm might not have exchange and kana, either. Tracking also changed considerably that having become long 80 mm equipped with the wide wheel of 3.50-8 of the daytona as for the wheel. Although it is with regulation before and after a troublesome axle shaft is quickly possible by a quick chain adjuster mechanism, there is no detailed explanation and it does not understand quite well.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!