4,980.58 PKR
(2,708 JPY)
4,548.37 PKR
(2,473 JPY)
(9% OFF)
4 (21 Reviews)
Very Good
Takes some getting used to?I tried to replace Seal because I removed the Caliper, but it was on the way. "Oh, that's easy! . But I couldn't pull out the whole thing because I couldn't spread it out and lift it up.
Reviews For MINIMOTO Brake Piston Pliers From Other Webike User
Terrible
Sadly these did not work for meAbout quality and texture - The whole tool is made of quite thin materials and feels undersized. For example, the handle has square edges and even with the covering it hurts to hold this tight in your hand and turn it. I found that I needed to hold it tight before turning as the lock screw is very thin (M3 size?) and if felt that if I tightened it too tight i would just cross thread it or round it off, although the folded steel bracket that holds this screw bends when you tighten as well so maybe its poor design (only held on one side) would stop that? About the feeling of use - It hurts to use this tool on an old caliper that needs a lot of pressure. I expect this would be ok on something that was in good condition, but on an old rusty caliper (with clean piston faces) this tool did not work. The (looks hardened as you can see in the photo) grips in the 'jaws' dug deep into the old piston inside edges and ripped the steel. Not something you would wish for if you wanted to keep those pistons. About Design - I think the deisgn is good but this set is cheaply made and I expect not the best example of the design. It is certainly not strong enough for being used on an old caliper where is piston is tight as that needs force to move it free, but I think that is probably the only reason DIY people like me would buy this tool. So, I have to say the design is 'bad' in this case.Cost performance and comparison with other products - It is cheap, but for my use it was money wasted. I didnt break it so I can at least use it on other (better) calipers, but it didnt do the job I wanted even when I heated the caliper. So I spent money on a tool and am no further forwards. There are other tools that look similar and I would look at those instead of this one.About shipping and packaging - shipping was fast and it was well packed.Any concerns, cautions, or advice when purchasing - I would not purchase this tool again and I suggest any potential buyer looks for another version that is built much more strongly if they are trying to work on old calipers.View Detail
Excellent
CaliperOverhaulI purchased this for CaliperOverhaul.
It will be a dedicated tool for that purpose, so there is no other use for it. If you are going to borrow it from another source, it would be better to do so.
Now, I don't have such a reliable friend, and the choice was to pay a Motorcycle shop to do it for a high labor charge or to do it myself, and then TotalCost becomes an issue.
How much would it cost to get the tools myself? If it costs nearly 100,000 yen just to get the tools, I would not hesitate to ask a Motorcycle shop to help me. I think I can do it. Thanks to finding this product, which is very cost-effective, I have decided to do it by myself.
By doing it yourself, you can take your time to clean and check. This time is fun. Of course, self-responsibility is the primary requirement. Prepare well and find someone to talk to if you think it is not going to work.
You had not yet given me any feedback on how you used it.
It is inexpensive, so it may be adequate, but the grip is so thin that removing a lot of pistons hurts my hands. Wrapping a tubular sponge or rubber around it will improve the pain. Also, if the piston diameter is small, the grip width is large, so it is hard to handle.
But it was cheap, so I am satisfied.View Detail
Very Good
It is easy to useThis was the first time I rode Brake's Piston, and I was pleased with how easy it was to use. However, since I have an air compressor, I don't think I needed it.View Detail
Very Good
Lock Function is very useful!The night of 15 when I thought that all Piston Extractors were the same.
Piston polish that was convenient to use the lock mechanism this time
BlueMagic is seriously awesome!
Well, what I'm trying to say is, congratulations on your marriage, Gacky!View Detail
Most Viewed Reviews Of MINIMOTO Brake Caliper Tools
Terrible
Sadly these did not work for meAbout quality and texture - The whole tool is made of quite thin materials and feels undersized. For example, the handle has square edges and even with the covering it hurts to hold this tight in your hand and turn it. I found that I needed to hold it tight before turning as the lock screw is very thin (M3 size?) and if felt that if I tightened it too tight i would just cross thread it or round it off, although the folded steel bracket that holds this screw bends when you tighten as well so maybe its poor design (only held on one side) would stop that? About the feeling of use - It hurts to use this tool on an old caliper that needs a lot of pressure. I expect this would be ok on something that was in good condition, but on an old rusty caliper (with clean piston faces) this tool did not work. The (looks hardened as you can see in the photo) grips in the 'jaws' dug deep into the old piston inside edges and ripped the steel. Not something you would wish for if you wanted to keep those pistons. About Design - I think the deisgn is good but this set is cheaply made and I expect not the best example of the design. It is certainly not strong enough for being used on an old caliper where is piston is tight as that needs force to move it free, but I think that is probably the only reason DIY people like me would buy this tool. So, I have to say the design is 'bad' in this case.Cost performance and comparison with other products - It is cheap, but for my use it was money wasted. I didnt break it so I can at least use it on other (better) calipers, but it didnt do the job I wanted even when I heated the caliper. So I spent money on a tool and am no further forwards. There are other tools that look similar and I would look at those instead of this one.About shipping and packaging - shipping was fast and it was well packed.Any concerns, cautions, or advice when purchasing - I would not purchase this tool again and I suggest any potential buyer looks for another version that is built much more strongly if they are trying to work on old calipers.View Detail
Excellent
CaliperOverhaulI purchased this for CaliperOverhaul.
It will be a dedicated tool for that purpose, so there is no other use for it. If you are going to borrow it from another source, it would be better to do so.
Now, I don't have such a reliable friend, and the choice was to pay a Motorcycle shop to do it for a high labor charge or to do it myself, and then TotalCost becomes an issue.
How much would it cost to get the tools myself? If it costs nearly 100,000 yen just to get the tools, I would not hesitate to ask a Motorcycle shop to help me. I think I can do it. Thanks to finding this product, which is very cost-effective, I have decided to do it by myself.
By doing it yourself, you can take your time to clean and check. This time is fun. Of course, self-responsibility is the primary requirement. Prepare well and find someone to talk to if you think it is not going to work.
You had not yet given me any feedback on how you used it.
It is inexpensive, so it may be adequate, but the grip is so thin that removing a lot of pistons hurts my hands. Wrapping a tubular sponge or rubber around it will improve the pain. Also, if the piston diameter is small, the grip width is large, so it is hard to handle.
But it was cheap, so I am satisfied.View Detail
Very Good
It is easy to useThis was the first time I rode Brake's Piston, and I was pleased with how easy it was to use. However, since I have an air compressor, I don't think I needed it.View Detail
Very Good
Lock Function is very useful!The night of 15 when I thought that all Piston Extractors were the same.
Piston polish that was convenient to use the lock mechanism this time
BlueMagic is seriously awesome!
Well, what I'm trying to say is, congratulations on your marriage, Gacky!View Detail
Other Reviews From Japanese Webike user
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING